Sovol Matte PLA Filament Rotated Tri Color Co-Extrusion 1.75mm, Fast Change 3D Printer Filament 1kg/ 2.2lbs, Matte Red Green Blue 3 in 1 Coextrusion PLA Material +/-0.03mm

It works great, it’s cheap, and easy to load.
This machine has brought filament left in the garage open in the rainy pacific north wesr for years back from the dead.I stopped printing about 3 years ago when my ender printer died. I just got a bambu printer and using some of that old pla just led to a stringy mess.I have the ams light so can do 4 colors at the same time, but driers that could hold 4 filiments are expense.And that brings us to our clearly repurposed toaster oven body (it does not have the same heating element, but instead something that can only lightly heat the area).Yep, it’s not silent but not not really any louder than a running printer. Just a light repeating him.It leave it on all the time baking whatever I need next, and it seems fine and safe temperature as I can put my hands on all the internal surfaces and it is just warm.Everything I put in there for 12 hrs (my typical overnight time) prints like a dream even if it was a crunchy mess before.I live in an area that is technically a rainforest with super high humidity and the printer is running in near freezing temperatures, and with a warm spool from this thing, it is no problem.Also it’s nice to just open the door and slide in a new roll. They just glide in like a slice of toast and no complex closing mechanism.But yeah, it’s cheap and it works. Just grab the darn thing before they run out of toaster bodies to repurpose to make these.

Exactly as described
Bought the SH01 Filament Dehydrator for testing. When testing I looked at the function of the dehydrator compared to the advertisement listed on Amazon. Based on this I would give it a 5 star. It is exactly as described and functions well. I was able to get 15% humidity at 50c when leaving the latches unsecured. The directions are easy to understand and even advise to leave the lid propped open to allow moisture to escape.Positives –1) Includes fan to circulate air inside the case.2) Can be used as a storage box when closing off holes using attached plugs.3) Easy to program.4) Good quality build.5) Easy to understand directions.6) Large dryer, can dry two rolls at one time saving cost of two dryers.I gave it a 4 star based on the following factors.1) Temperature is 40, 45, or 50. However, this may be a good feature for many. It was not a factor for me as I run my other dehydrators at 50c.2) Timer can be set from 6 to 12 hours. Would like to see at least 24 hours.3) The holes for feeding filament are on top. Would be good to have holes in the front also. It will not work as well if you mount the dryer above your printer as it will lead to filament binding in the holes. This will be an easy fix by drilling two holes in the front and inserting Pneumatic Fittings. However, this will take away from using as a storage box and may void warranty.4) The bottom gets hot while using. Found some feet on Thingiverse you can print to raise it which will help with this issue. Sovol 3D – DUAL Filmanet Dry Box Stand Off5) Takes a while for the temperature to raise to set value. This may be due to it being larger and holding 2 rolls of filament.Overall – This is a quality dryer and will make an excellent standalone dryer for filament. When placed beside the printer it will also work to keep filament dry when running long prints. Would highly recommend to use with a dual head printer.

Works as designed.
I purchased this to be able to dry 2 rolls of filament for my 3D printers. This is especially important for the PETG that I use as well as the PLA, I do not use ABS. As stated in the “About this Item” information on the Amazon site, it cycles back and forth between the Temp/Humidity and drying time. The first time that I turned this on I was quite concerned because I could smell the electrical smell. I turned it off and checked it out to make certain it was ok. I think that it was just getting rid of that “new” smell.I turned it on again and programmed it for 6 hours of drying time. The “Work” was showing on the unit, but it shut off after 6 minutes. So I tried it again, and it seems to be working ok now.There is just a simple small piece of paper for the instructions. Most filament dryers are fairly intuitive and this is one pretty ease to understand as well.You are able to use the filament direct from the dryer to your 3D printer, but I don’t do that. The unit is lightweight coming in a 3.65 lbs. I had nice sized footprint 9.69x 6.89 x 9.53″. I have the white model and I feel it looks nice.I’m pretty happy with this purchase. I hadn’t thought of placing the desiccants into the dryer with the filament. I like that idea as well. When the time is completed, it emits a loud beep telling you it is done. That is a nice feature as well. It is extremely quiet and I don’t even notice it is on.

I’ve been looking at various filament dryers for quite a while (including on Aliexpress) and this seems to be the best thing going for what you get.There are several less expensive dryer boxes that will dry one roll at a time, but this is the only one that I’ve seen that will do two at a time (or one really large roll).Unlike most of the others, this unit also has a seal that the lid sits in, clasps to hold the lid closed, an internal fan, and shows the humidity (not just temperature).I have seen people modify other dryers to add some of these features, but after the trouble and cost of the modifications those boxes still only hold one roll at a time. This is still more economical than buying two un-modified single roll dryers.This dryer preforms quite well and has brought some life back into some of my older rolls of filament. Since this has a proper seal it will also keep a roll dry even when it’s done. I now have a muti-filament (3) 3D printer and I have ordered a second dryer so I can keep three rolls plus a spare dry all the time while printing.You can set 3 different temperatures (40C, 45C, & 50C) and drying time from 6 to 12 hours. The box heats well and seems quite stable, and you can really only hear the fan when the lid is open (will update if it gets noisy). There are touch sensors for the three buttons on the front, and the backlit display is very legible. The external power supply gets warm but not hot and I’ve had it running for days without any issues so far.It has two filament holes on the top of the lid, with seals, and a seal for the power plug on the back. The only thing that would have been nice is extra filament holes on the back (or front) for alternative routing options.I’m quite happy so far and would recommend this over the single roll dryers (even if you only really need it for one roll at a time)5 star product 🌟🌟🌟🌟🌟

I’ve had nothing but issues with this filament, poor adhesion and blockages/ clogs. I know you might be thinking that’s user error, but I have tried various changes to settings and drying etc. but still every print fails. I even replaced the hot end just in case. I have used four other brands of filament and literally never had these issues. I would not recommend.