AMOLEN PLA 3D Printer Filament, PLA Filament 1.75mm Silk Shiny Filament Red Gold Filament, 3D Printer Gradient Pla Filament 1KG/2.2lb Compatible with Most FDM 3D Printers

Works Flawlessly and Looks Beautiful.
This is a great filament! The print quality is astonishing on any settings and I can always rely on the adhesion to be perfect. The shine and deep color of this PLA makes this by far my favorite filament to print my Flexi Phoenix with. Everything always comes out looking and feeling great from test prints to final products. This is a must buy for any Flexi Factory model!

Good value for sample materials
I bought this sample pack to test out AMOLEN’s products. I’ve printed a few parts with each sample spool. I used the same bed temperature for each spool, 65C initial layer, 60C for the rest of the print. Winding was good except for the marble, and that was only for some outer windings.Silk Copper: This was my most successful of the four sample materials. I printed a temperature tower, small keychain for my wife and a T-Rex skull. I used a print temperature of 200C for the keychain and skull. Adhesion was great and the parts came off with small amount of effort after the bed cooled. I printed at 0.12mm layer thickness for the skull and it looks amazing! I used 0.2mm layer height for the keychain and tower and they’re both smooth with no defects. You’ll see some stringing in the temp tower and skull, this might be remedied with some print settings.Silk Gold: This was by far my most difficult material. I tried printing at 200C with 0.3mm nozzle but after about 30 layers it would clog up. I switched to a 0.4mm nozzle and it lasted a little longer. I ended up printing a temp tower after trying IronMan four times. I made some adjustments and semi-successfully printed Iron Man the fifth time. He was still really stringy and the detail wasn’t that great, this could be due to scaling it too small. I ended up using a print temp of 215C. This filament was pretty brittle compared to the other three and snapped on me once while switching it out.Marble-like: I didn’t have too many issues with this material. I printed a test cube and Minas Tirith (a city from Lord of The Rings) at 200C and it behaved well, but there was quite a bit of stringing on the city that I had to clean up. Otherwise, the part looks great! The spool was wound pretty bad for the outer windings and bound up a bit as the city printed. The inner windings look better though.Glow in the dark: This was the most fun to print with so far. I printed Zero from Nightmare Before Christmas for my daughter. The nose and collar were printed from orange and red PLA. I printed the glow in the dark at 200C and it was REALLY stringy. I super glued the parts together (Gorilla Glue brand) and they stick together great. The material glows really well, especially if it gets direct sunlight.

Tangled Spool
I got this spool in 2022. First time I tried to use it, I had problems with layer adhesion and extruding. Tried all sorts of temps (including the recommended ones listed right there on the spool) I have a flash forge adventure 3. For the life of me I could not get it to adhere properly to the print bed and anything remotely salvageable looked terrible. Not good for any sort of detail work / anything “complicated”Second time I used it, it clogged so horribly I had to replace the printer head on my printer because I could not clear the clog at all. (Trust me, I tried everything) and I also had to replace the tube & coupling that fed the filament into the printer head. This clog was so bad I had to disassemble the feed assembly as well. Had it not been for the ease of getting flash forge parts from there site and how easy it is to pull the printer appart, it would have killed my printer irreparably. I tossed it in a bag with oxygen absorbers and promptly ignored it, and basically dubbed it the cursed spool.I’ve learned a lot since that point and decided to touch the cursed spool again. I decided to print off a very simple print that many other of my “difficult” filaments from other manufacturers seemed to do really well with. I recognize that “silky” filaments are notorious to be difficult but I have others from different manufacturers and *never* had a problem like this one.I DID NOT REALIZE THE ENTIRE SPOOL WAS A KNOTTED TANGLED MESS. I regret not returning this when I had initially got it, but that was primarily due to my inexperience at the time. It was among some of the first filaments I had gotten and didn’t know better. I some how managed to get a print out of it (it’s a split color, so the first 15 layers of the print are in an entirely different filament) and you can see how deep that tangle of filament ran on the spool.Then I looked deeper into the roll. You can literally see it runs throughout the entire roll how tangled the whole thing is.

servizio prime sempre ottimo, non ho ancora provato il prodotto packaging ottimo tutto sottovuoto i colori sono come da foto appena lo avrò provato lo descriverò.

Un gran filamento, realmente estoy muy satisfecho con su calidad, volveré a comprar

Das Produkt an sich ist gut……aber von 2 farbig kann nicht wirklich die Rede sein……es ist eher ein flipflop Filament mit Glitter in Grün. Ich bin hierbei eher von einem Filament in in der Art wie Regenbogen Filament ausgegangen. Also mit Farbverlauf.Haftung und Qualität ist aber Gut bis sehr gut. Nur halt die Beschreibung hatte ich anders interpretiert…..